Business Writing for Results in Software

Create Data Matrix ECC200 in Software Business Writing for Results

transmission index but also in selecting the longest possible dwell or reversal of motion. It is also worth noting that unless the transmission index is zero, a single dwell of 180 or more is not possible. Furthermore, shorter dwell or no dwell at all implies that the transmission index is greatly improved. This is a useful feature in designing a mechanism for prescribed function generation without a dwell. 4. Figure 8.22 shows a (-dh/dq) vs q curve drawn along with the solution curves for n for sample values of (r/d ) and (d/a). Recalling Eq. (8.17), it can be seen that the (dh/dq) vs q curve is the average of two segments of the solution curves for n. Therefore, by re ecting the n curve for the range (0 q p) about (-dh/dq) vs q curve, we get n curve for the range (p q 2p). This makes the prediction and control of the output motion of the cam in the second half of the cycle possible, as Eq. (8.17) is true for any value of n, not just the solutions of Eq. (8.27). It should be noted that (-dh/dq) is independent of the transmission index (r/d). It is also worth noting that by choosing n along the (-2dh/dq) curve, n* can be made zero to get a dwell in the second half of the cycle. 5. The area under the n vs q curve gives f, the rotation of the cam that can be used to generate the cam pro le by using the kinematic inversion shown in Fig. 8.17. 8.12.3 Design Procedure Using the results of the foregoing analysis, a systematic procedure for designing a fully rotatable, roller-crank driven cam mechanism for arbitrary motion speci cations is described in this section. An important design speci cation is the minimum value the trans-

Downloaded from Digital Engineering Library @ McGraw-Hill (www.digitalengineeringlibrary.com) Copyright 2004 The McGraw-Hill Companies. All rights reserved. Any use is subject to the Terms of Use as given at the website.

Part II:

Factors for 1000 are: 2 4 5 8 10 20 25 40 50 100 125 200 250 500

Marine connectors differ from residential wiring connectors in being subject to vibration and other stresses. Figure 6.12 is self-explanatory and shows both approved and disapproved types of connectors. Note speci cally that the ubiquitous wire nut, so popular in household wiring, is not approved for marine use. Friction-type connectors (blade and bullet connectors, shown in Figure 6.12) can be used provided they resist a pull in the direction of the conductor of at least 6 pounds for 1 minute. The other connectors in Figure 6.12 must resist the tensile forces shown in Table 6.7 for at least 1 minute.

Distance FSO technology performs with exceptional reliability when used over comparatively short distances, something in the order of tens of meters to a few hundred meters. However, when used over longer distances, it becomes less reliable during atmospheric events such as fog and heavy rain. Therefore, in order to achieve fiber-like reliability, it is necessary for the lengths of FSO links to be fairly short. The multihop capability of a mesh network allows the lengths of FSO links to be maintained at less than a few hundred meters. Point-to-multipoint FSO is a point-to-point technology and, therefore, cannot, by itself, provide point-to-multipoint services. This shortcoming of FSO is complemented by mesh networking technology, which can offer both point-to-multipoint and multipoint-to-multipoint services. Line-of-sight FSO technology is a line-of-sight technology. Therefore, FSO by itself cannot be used to offer its high capacity network services to a location not in line-of-sight of a POP. However, mesh networks enable delivery of services to locations that are not in direct line-of-sight of the POP. Failure resiliency All communications systems are prone to failure and FSO links are no exception. Because of its line-of-sight requirements, any event that could rob an FSO link of its line-of-sight would disrupt the link. This limitation is complemented by the redundancy inherent in mesh networks.

A powered-up physical layer connection to the device is attached to the port. Traffic is entering and/or leaving the port. An operational problem is occurring with the port perhaps excessive errors or a connection problem. The port has been disabled manually (shut down), disabled because it is in a blocking STP state, or disabled because of a security issue. No powered-up physical layer connection exists on the port.

Effect box surrounding the Graph Paper object. Hold CTRL to constrain the movement of your cursor to the first direction in which you drag, and then drag down to about the second or third cell in the right column, as shown here. You ve created a Perspective effect on the object, as you can see the cells align more or less with the effect s red-dotted overlay reference, and a vanishing point appears directly to the right.

Ill 18-12

27:

However, the reverse is not true. Local variables declared within the inner scope will not be visible outside it. To understand the effect of nested scopes, consider the following program:

6. Click Add so that elements from these three tables become universe classes and objects as shown in the following example. If you click the + sign next to any of the individual classes, you will notice that Designer has added all the columns in each table with a blue box next to the item to denote a dimension. These symbols and object types are discussed further in 9.

provided this last limit exists as a nite or in nite limit. Let us learn how to use this new result. EXAMPLE 5.1